Showing posts with label Frank Kaczmarek. Show all posts
Showing posts with label Frank Kaczmarek. Show all posts

Franks wooden fish all set to ride.

Frank is a bus driver here on the Gold Coast and loves to get out for a surf. This is his second wooden board and I designed this fish for him. Hollow wooden framed construction and its all come out as a great looking board. Many hours work will be enjoyed over the coming summer.

" Well, it's finally finished and here are the pics. I'm pleased with the result and will now be waxing it up to try it out. It's considerably lighter than the mal I built last year, and hopefully it will perform OK. If the fins don't do the job I hope they will I can try different types of fins. The leash plug is one with the Goretex breather built in, so I won't have to worry about doing the plug up or losing it.
The final measurements are 7'6 3/4" x 22 1/2" x 2 5/8", so the size is spot-on to the original plan."





If you would like to check out Franks progress click here

Franks fish all ready to ride


Frank with the board all strapped down and getting the rails sorted.This is his second wooden board he has built.
" Well, it's finally finished and here are the pics. I'm pleased with the result and will now be waxing it up to try it out. It's considerably lighter than the mal I built last year, and hopefully it will perform OK. If the fins don't do the job I hope they will I can try different types of fins. The leash plug is one with the Goretex breather built in, so I won't have to worry about doing the plug up or losing it.
The final measurements are 7'6 3/4" x 22 1/2" x 2 5/8", so the size is spot-on to the original plan"



Franks own fin design to be tested in the coming weeks.


Great looking board Frank and look forward to the ride report.

Franks progress report...

Frank has been busy building his fish at home in the garage and just sent in these updates to share.
" I cut all the short pieces @ 45 degrees , taped them together and edge glued them, a total of 96 pieces. "

" The four composites so created were then glued to the frame like the other planks."

" And as you can see one can never have too many clamps.Because the two timbers , i.e. the paulownia and the western red cedar do not bend equally under the same pressure I had to insert an extra 3/4 length stringer on each side to provide a fulcrum to bend the 45 degree pieces evenly to make the curve of the deck as it rolls down toward the rails. "

" Near the tail I inserted a foam block on each side to anchor the fin boxes. There is also a foam block to take the gore-tex leash plug/vent near the V of the tail."

" Now I am starting to laminate the rails, starting with the V in the tail. The rails will be alternate layers of paulownia & w.r. cedar. I have also started on the fins, working on them while waiting for the glue used in the lamination to set."

" I don't know if the board will be finished by August the 8th, but I will bring it along regardless."

Frank is a bus driver here on the Gold Coast. Loves his surfing and has been building the board between shifts on the buses. He has set himself a tricky job with all the detail with different timbers and angles , but the result looks great . This is his second board and just shows once you get the bug you are willing to challenge yourself to build something personal and different.

Great job mate and we look forward to catching up in August.

Franks new fish takes shape

I Designed a fish for Frank to build as his second board and he has just sent me some pics and info to share .
"The fish board has been started and is progressing quite well. I now have all the timber I need for it and have some progress pics for you. I had the plan shapes printed full size by the plan printers in Southport as you suggested and then cut them out to use as templates."

" This is going to be a more lightweight build than the longboard, with the frame constructed of 4mm marine ply and having only one 4mm centre stringer. At the beginning of the frame construction it was not nearly as rigid as the longboard, but once the rails were on it was much improved "

The frames seem to be coming together really well.


" For the centre board for the deck and bottom I wanted something strong as well as contrasting, choosing the hardwood amoora. With the amoora glued on top and bottom of the centre stringer and having fibreglass fillets on all four inside corners there is now a very strong I-beam the length of the board."

" The remainder of the board will be built using paulownia and western red cedar with two hardwood fins. "

Frank has gone with adding each plank one at a time rather than a skin layup as this is what he is comfortable with. There are no right and wrong ways of doing any of your building project. We all have different ideas and amounts of time , tools and resources to put to use.So just be comfortable with what you are doing and nut it out your way is fine.

Thanks Frank for sharing you project.

Frank has finished his board

Frank Kaczmarek snapped his favourite foam board so he set about building his first wooden board by slicing up his foam one to get the templates to build the wooden one.You can see his project in a couple of earlier posts. Frank also brought his unfinished board to the wooden board day. It created a lot of interest as people were very interested in the frames and what was happening inside.
" Well, The board is finished (at last) . I ended up doing all the glassing and final polishing myself, and while not as good as a professional job I'm glad that I did everything myself.
I've had a couple of surfs on it at the sandpumping jetty on The Spit on Sunday and Monday mornings. It takes a bit of getting used to and is of course heavier than my former fibreglass board it was modelled on.
I'm pleased with the result and will be surfing it regularly. I'm getting a lot of interest and questions from other surfers who want to know about the construction and what sort of timber was used. Now comes the task of tidying up the garage so my wife can put her car in there again.
Thank you for your help and advice and I look forward to seeing you at the next wooden board gathering if not sooner somewhere in the surf. "



The longboard progesses...





Local surfer Frank Kaczmarek is getting into his project to build a wooden version of his foam board that he snapped in two.He is hoping to have it finished for August , or will bring it along to the park anyway. Mate there is a lot of work in building a board for the first time and looks like you are getting on top of it now.Thanks for sharing and we look forward to the finished project.

From foam to wood - Frank Kaczmarek




This is what you can do when you break your foam board and you want a project to keep you busy.This is Franks story...







" Hi my name's Frank Kaczmarek and I live on the Gold Coast at Labrador. Earlier this year I broke my 9' "Evolve" longboard in a nasty head-high barrel that closed out on me at Burleigh. The board was custom made only a year earlier by Darren Dobbie. I ended up with two halves and no justification to spend another $1000 for a board, so decided to build my own. I'm quite handy with wood so I thought I'd give it a try. After looking on the web I put together a few Ideas and worked out my way to do it. I cut the remains of the old board into sections and made templates for the new board. I built a folding workbench from leftovers in the garage to work on, and to keep everything straight I've screwed right angle brackets to the bench and then clamp the centre stringer to that.
The board I'm building has a 4mm marine ply frame with a laminated 8mm centre stringer. The deck & bottom will be a combination of the marine ply strips, western red cedar strips from a local blind & shutter manufacturer and paulownia strips from John White. John is the one who passed on your Blog and email address to me.
As I work full time I am working on the board whenever I can, which is not as often and as much as I would like to.
I am now trying to finish the board by August so I can bring it along to the Alley on the 9th.
When finished it should be 9' X 23"X 3" approx.
Hope to see you at the alley in August."
Cheers,
Frank.

Thanks Frank for sharing your project and we look forward to progress reports and a ride review in August at The Alley.